ABB ACS150 USER MANUAL PDF

ABB ACS Operation Limits. Setup the For settings of other parameters/ macros and detailed explanation hereof, see the instructions manual from ABB. View and Download ABB ACS user manual online. ACS Controller pdf manual download. The ABB ACS series component drives are easy to select and come with a variety of standard features acsuser-manual-partpdf.

Author: Voodooshicage Megis
Country: Denmark
Language: English (Spanish)
Genre: History
Published (Last): 25 January 2008
Pages: 254
PDF File Size: 17.89 Mb
ePub File Size: 8.11 Mb
ISBN: 164-9-60904-444-5
Downloads: 8789
Price: Free* [*Free Regsitration Required]
Uploader: Tojat

Strip the outer insulation of the analog signal cable degrees and ground the aca150 shield under the clamp. Other values can be used if a static speed error is detected despite of the full slip compensation.

ABB ACS – KW – IP20 – ACSEA – Drives Online Ltd

Compatibility The manual is compatible with the ACS drive firmware version 1. Maintenance Fan failure can be predicted by the increasing noise from the fan bearings. Page 52 Step Action Display Use keys to select the parameter value.

Motor cable shield To function as a protective conductor, the shield must have the same cross-sectional area as the phase conductors when they are made of the same metal. A Value is at or below minimum limit.

Industrial Component Drives ACS | Variable Speed AC Motor Drive (ABB) | ECD Controls

A Value is at or above maximum limit. Hardware Description Manaul chapter describes the construction and abh code information in short. For the parameter default values, see section Default values with different macros on page Free space around the drive The required free space for cooling above and below the drive is 75 mm 3 in.

  AFZAL UL FAWAID PDF

Selecting The Power Cables Selecting the power cables General rules Dimension the input power and motor cables according to local regulations. The type code contains information on the specifications and configuration of the drive. Ignoring the safety instructions can cause injury or death.

Brake resistors ACS drives have an internal brake chopper as standard equipment. Page 20 Fasten clamping plates 1.

ABB ACS150 – 0.75KW – IP20 – ACS150-01E-04A7-2

The drive monitors whether certain user selectable variables are within the user-defined limits. Changing this parameter setting is not recommended. Mounting The Drive Free space around the drive The required free space for cooling above and below the drive is uder mm manyal in.

You find more detailed instructions on setting parameters on page Installation Checklist Installation checklist Checklist Check the mechanical and electrical installation of the drive before start-up. Installation And Commissioning Flowchart Installation and commissioning flowchart Task Identify the frame size of your drive: Manhal and signals in the Long Parameter mode The following table includes the complete parameter and signal list, i.

Page 28 Planning electrical installation Current Contact your local ABB representative. Set constant speeds drive output frequencies 1, 2 and 3 parametersand Constant speed selections are ignored if accs150 is in local control mode. Corresponds to the minimum setting of the used source signal.

  BORDOGNI ROCHUT PDF

The dimensions are given in millimeters and [inches]. Without plates R0 and R1 Page Save the parameter value by pressing Enter the motor data from the motor nameplate: Fault Tracing An alarm or fault message on the panel display indicates abnormal drive status.

For correct manul selection, contact your local ABB representative. Electrical installation What this chapter contains The chapter describes the electrical installation procedure of the drive. Analog signal if connected: Page 23 – Selecting the power cables Page 24 Page 25 – Protecting the relay output contact and Step Action Display Use keys to select the parameter value.

Go through the checklist below together with another person.

For example if XXX is 8A8, nominal current is 8. Page 49 Output mode In the Output mode, you can: The user may set limits for speed, current etc. Planning electrical installation on page Check the ambient conditions, ratings and required Technical data on page cooling air flow.

When it is on, the drive starts, accelerates to a preset speed at a preset rate. The ACS has five application macros.

Page 50 Reference mode In the Reference mode, you can: