ELASTOPHENE FLAM 25 PDF

ELASTOPHENE® FLAM 25 AR T3 is a SBS elastomeric bitumen waterproofing membrane with a glass grid / glass fleece reinforcement. The topside is protected . ELASTOPHENE® 25 AR must be applied by torch-on techniques on a weldable underlayer (FLAM) or bonded with bitumen (EAC free of oxidized bitumen) on a. ELASTOPHENE® FLAM is a flexible SBS elastomeric bitumen waterproofing membrane with a non-woven polyester reinforcement. Both sides are.

Author: Majas Zolokazahn
Country: Guadeloupe
Language: English (Spanish)
Genre: Health and Food
Published (Last): 11 March 2008
Pages: 318
PDF File Size: 19.53 Mb
ePub File Size: 18.24 Mb
ISBN: 807-4-65907-227-7
Downloads: 21448
Price: Free* [*Free Regsitration Required]
Uploader: Nanos

These are ajusted now but will be fitted later taking into account the future height of the finished surface. Click on photo to enlarge. L’isolation Knauf Thane ET.

ELASTOPHENE FLAM | SOPREMA

Il est bien plus rapide de remplacer les renforts par le flashing: Cinq points de Sopracolle par plaque. For example the first layer could be elastopgene, and the insulation glued directly to the existing surface. Finishing around rain water collector See 2.

Since the new waterproofing and the insulation will raise the roof, the rainwater drains must also be raised. The figure shows the three layers and the sidewall reinforcement for each layer. Bitumous glue is applied to the rising side walls.

  EBOOK BIOGRAFI BJ HABIBIE PDF

Creative Commons Attribution – Pas de Modification 3. Finition autour de la platine. Before the insulation is laid, the channels carrying the rain water are reinforced: As with the 1st layer, the joint of the flat roof and the rising walls that surround the roof are a possible source of leaks. The Elastophene 25 is rolled out and cut to fit.

ELASTOPHENE® FLAM – Soprema

The rain water collector will pass through this. The collector is trimmed before applying the outer reinforcement. Because there are few right angles, there are lots of triangles to be filled in. The time has come to re-do the waterproofing on the terrace roof of my house. elaxtophene

Reinforcement at junction of standups. Before work begins, the existing concrete surface was cleaned with a high pressure bar hose equipped with a rotating jet.

Rodolphe Ferracane, e-mail contact AFR-etancheite.

Good waterproofing requires a reinforcing piece between the roof and the wall. Click on the photos to enlarge them.

Fitting the 2nd layer in front of the future rain collector. If there is a risk of rain, then the Knauf Thane ET glued to the first layer must be entirely f,am by the second layer, even if this means performing work not needed by the final waterproofing.

  INTEGRALE IMPROPRE EXERCICE CORRIG PDF

Cliquer sur les photos pour les agrandir.

The top serface is covered with flakes of stone which protect it against the ultra-violet. When reading estimates for waterproofing on flat roofs you may find that the estimate is lightened to reduce the price.

The orientation of the second layer depends on the way in which the third layer will be applied. The two layers should be perpendicular to one another. Creative Commons Attribution – NoDerivs elastphene.

ELASTOPHENE® FLAM 25 AR T3

The joint of clam flat roof and the rising walls that surround the roof are a possible source of leaks. Cutting nord end of a roll of finishing layer. The third bitumous layer is a reinforced bitumen with its lower face covered by a film which melts when heated, gluing it to the second layer.

The rain water collector is positioned through a hole cut in the sidewall reinforcement, and then heated to glue it to the sidewall.