LA3600 DATASHEET PDF

LA datasheet, LA circuit, LA data sheet: SANYO – 5-Band Graphic Equalizer,alldatasheet, datasheet, Datasheet search site for Electronic. LA datasheet LA component LA integrated circuit LA schematic LA application note A LA LA36 LA3. Sanyo LA datasheet, 5-Band Graphic Equalizer (1-page), LA datasheet, LA pdf, LA datasheet pdf, LA pinouts.

Author: Yozshurr Kagalar
Country: Canada
Language: English (Spanish)
Genre: Spiritual
Published (Last): 9 December 2013
Pages: 34
PDF File Size: 18.65 Mb
ePub File Size: 13.34 Mb
ISBN: 769-7-70017-474-4
Downloads: 14002
Price: Free* [*Free Regsitration Required]
Uploader: Vira

Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response. Your email address will not be published.

LA datasheet & applicatoin notes – Datasheet Archive

In the circuit capacitors C1, C3, C5, C7 and C9 are used to fix the resonance frequency of the corresponding bands. How we connect stereo input to this circuit?

This will hold good only when following are carried out. You may also like: Capacitor C13 is a decoupling capacitor and C14 is datashdet power supply filter circuit. Your email address will not be published. Assemble the circuit on a good quality PCB. Most of the IC manufacturers call their multi band tone controls as graphic equalisers.

Datasheet «LA3600»

The LA can be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads. Previous post Next post.

Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5. Leave datadheet Reply Cancel reply Your email address will not be published. This will hold good only when following are carried out.

  A COMPREHENSIVE SPANISH GRAMMAR JACQUES DE BRUYNE PDF

LA3600 Datasheet PDF

Previous post Next post. LA is a single integrated single Op-amp, 5 band graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc. How we connect stereo input to this circuit? Hi Eric Nice question. You may also like: Could i add this to my homemade tube amp, and take out the LA?

The power supply must be well regulated and noise free. Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5. The LA can be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads. Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response.

Leave a Reply Cancel ratasheet Your email address will not be published. Then the contour of the knobs represents the frequency response of the tone control unit. I used 9V DC for powering the circuit. C12 is the output capacitor and resistor R6 limits the supply current. If you use slider potentiometers as controls and mount them vertically in a sequence from left to right as R1 to R5 and as you slide it down, should cut the frequency spectrum for which it is meant and sliding up should boost.

  DICTIONARY OF ECONOMICS GRAHAM BANNOCK PDF

Then the contour of the knobs represents the frequency response of the tone control unit. LA is a single integrated single Op-amp, 5 band graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc.

Assemble the circuit on a good quality PCB.

Could i add this to my homemade tube amp, and take out the LA? Hi Eric Nice question.

C12 is the output capacitor and resistor R6 limits the supply current. Most of the IC ,a3600 call their multi band tone controls as graphic equalisers. The power supply must be well regulated and noise free.

Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit. In the circuit capacitors Darasheet, C3, C5, C7 and C9 are used to fix the resonance frequency of the corresponding bands.

If you use slider potentiometers as controls and mount them vertically in a sequence from la33600 to right as R1 to R5 and as you slide it down, should cut the frequency spectrum for which it is meant and sliding up should boost. I used 9V DC for powering the circuit.